Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
The general information
Removal and installation of the forward stabilizer of cross-section stability and its plugs
Removal and installation of forward shock-absorbers
Removal and installation of a cross-section jet bar of a forward suspension bracket
Removal and installation of levers of a forward suspension bracket
Removal and installation of screw springs of a forward suspension bracket
Removal and installation of rotary fists
Replacement of spherical hinges
Removal and installation of a bar of the back stabilizer of cross-section stability
Removal and installation of back shock-absorbers
Removal and installation of a cross-section jet bar of a back suspension bracket
Removal and installation of levers of a back suspension bracket
Removal and installation of screw springs of a back suspension bracket
Removal and steering wheel installation
Condition check, removal and installation of a steering drive
Removal and installation of the steering mechanism
Removal and installation of the pump of system of hydrostrengthening of a wheel
Prorolling of system of hydrostrengthening of a wheel
Wheels and tyres - the general information
Corners of installation of forward wheels - the general information
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Removal and installation of levers of a forward suspension bracket
|
In avoidance соскальзывания картера the bridge from the position that considerably would complicate the subsequent assemblage, remove and establish each of suspension bracket levers serially. |
Поддомкратьте redock of the car also establish it on props.
The top lever
|
Give a nut and a bolt of fastening of the top lever to an arm картера the bridge.
|
Components of the right levers of a forward suspension bracket (the model 4WD is shown; for models 2WD the scheme is similar).
|
|
For a detachment of the top lever of a suspension bracket from картера the bridge give a nut (in a picture it is not visible) and a bolt (arrow), then take a bolt from an arm.
|
Give a bolt and a nut of fastening of the top lever of a suspension bracket to an arm of a frame and take the lever from under the car.
|
For a detachment of the top lever of a suspension bracket from a frame give this nut (marksman) and take a bolt (access to a bolt head is possible through an aperture in a frame, directed outside, towards a wheel arch).
|
Check up the lever on presence of cracks and deformation signs. The damaged lever replace.
Check up the plug in картере the bridge (only for the top lever) on presence of cracks, hardening and other signs of ageing of a material. If the plug requires replacement, establish the lever into place and drive away the car in a workshop of car-care centre or dealer branch where this work will be made by the qualified experts with application of the special tool without which presence plug removal is not obviously possible.
Installation make upside-down. All fixture tighten with demanded effort.
|
|
The bottom lever of a suspension bracket
|
With the help чертилки or paints put down adjusting labels on кулачковых regulators and the suspension bracket lever is will give a guarantee of correctness of the subsequent assemblage.
|
Before a detachment of the bottom lever of a suspension bracket from an arm картера the bridge mark position concerning it кулачкового a regulator, then give a nut and take a bolt.
|
Give a nut of fastening of the bottom lever of a suspension bracket to an arm картера the bridge, remove a cam and a cam bolt.
Give a nut and a bolt on an arm of a beam of a frame and lower the bottom lever.
|
For a detachment of the bottom lever of a suspension bracket from a frame arm give a nut (in a picture it is not visible) and take a bolt.
|
Installation make upside-down. Take care of combination of labels of mutual position of the lever and кулачкового a regulator. All fixture tighten with demanded effort.
|
|
|
|