Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   The general information
   Removal and installation of the forward stabilizer of cross-section stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross-section jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross-section jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and steering wheel installation
   Condition check, removal and installation of a steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Prorolling of system of hydrostrengthening of a wheel
   Wheels and tyres - the general information
   Corners of installation of forward wheels - the general information
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7

Removal and installation of screw springs of a forward suspension bracket

Removal

 PERFORMANCE ORDER

    Loosen the nuts of fastening of wheels, поддомкратьте redock of the car also establish it on props. Remove wheels. Mark position and disconnect forward карданный a shaft from the holder крестовины a leading gear wheel of differential (the Head Coupling and трансмиссионная a line), then tie up a shaft aside a wire piece. Prop up assemblage of the bridge by a jack got under differential or that is more preferable, two jacks - on one from each of sides of the bridge (last way will provide the best balancing). Отболтите from the bridge the bottom levers of a suspension bracket (Has undressed Removal and installation of levers of a forward suspension bracket). Отболтите connecting links (racks) of the stabilizer and shock-absorbers of a suspension bracket from the forward bridge (Sections Removal and installation of the forward stabilizer of cross-section stability and its plugs and Removal and installation of forward shock-absorbers). Disconnect from a bridge arm a jet bar (Has undressed Removal and installation of a cross-section jet bar of a forward suspension bracket). Disconnect average steering draught from сошки the steering mechanism (Section condition Check, removal and installation of a steering drive). Slowly lower bridge assemblage so that springs were completely stretched. If the bridge is propped up only by one jack, ask the assistant to support in the course of bridge lowering its right edge. Remove the holder of a spring and take a spring from under the car.
    Details of fixture of a screw spring - after the spring will be completely stretched give a bolt and remove the holder, then take a spring through space between the bridge and a frame.
    Check up a spring on presence of defects and traces of the corrosion, capable to be at the bottom of its premature exit out of operation.

Installation

 PERFORMANCE ORDER

    Establish a screw spring on картера the bridge, impose the holder on the bottom coil of a spring and strongly tighten a bolt of fastening of the holder. Lift the bridge in adjusting position and connect to it картеру the bottom levers of a suspension bracket (Has undressed Removal and installation of levers of a forward suspension bracket). Tighten fixture with demanded effort. Connect average steering bent for сошке the steering mechanism (Section condition Check, removal and installation of a steering drive). Fix a jet bar in the arm on the bridge (Has undressed Removal and installation of a cross-section jet bar of a forward suspension bracket). Connect to a forward part картера the bridge of a rack of the stabilizer and shock-absorbers (Sections Removal and installation of the forward stabilizer of cross-section stability and its plugs and Removal and installation of forward shock-absorbers). Connect forward карданный a shaft to the holder крестовины a leading gear wheel of differential (the Head Coupling and трансмиссионная a line). Establish wheels and nuts of their fastening, then lower the car on the earth. Tighten nuts of fastening of wheels with demanded effort (Specifications to the Head of Adjustment and routine maintenance see).