Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   The general information
   Removal and installation of the forward stabilizer of cross-section stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross-section jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross-section jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and steering wheel installation
   Condition check, removal and installation of a steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Prorolling of system of hydrostrengthening of a wheel
   Wheels and tyres - the general information
   Corners of installation of forward wheels - the general information
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions


e65f60b7

Condition check, removal and installation of a steering drive

Condition check

The steering drive serves for connection of the steering mechanism with operated wheels of the car and simultaneously provides adequate position of wheels the friend in relation to the friend. Into drive structure enter: сошка the steering mechanism, fastening its (mechanism) to a shaft and providing transfer of effort to average steering draught. Longitudinal back and forth motion of average draught is transferred to a rotary fist of the right wheel. Assemblage of connecting draught serves for connection of average draught with a rotary fist of the second wheel. Connecting draught consists of a pipe, collars and two tips. Демпфер the steering drive, established between average steering draught and a car frame serves for decrease in vibrations and undesirable loadings on components of the steering mechanism.

Components of a steering drive


 PERFORMANCE ORDER

    Establish forward wheels of the car in rectilinear position and block a steering wheel. Поддомкратьте one of car boats so that the wheel приоторвалось from the earth approximately on 3 see Establish стрелочный циферблатный a measuring instrument, having pressed it плунжер to external edge of a wheel. Undertake a wheel in forward and back points and pull it forward-back, watching measuring instrument indications. The maximum fixed value should not exceed 2,74 mm. If люфт steering system exceeds admissible, check up each of axial points and spherical hairpins of a steering drive on weak point presence. In case of need make replacement of components. Поддомкратьте the car also establish it on props. Check up covers of spherical hinges on presence of cuts, make sure of absence of the "become attached" hinges and damages or deformations of other components of a drive.

Removal and installation

Connecting steering draught

 PERFORMANCE ORDER

    Loosen the nuts of fastening of wheels, поддомкратьте the car also establish it on props. Cock a lay brake. Remove a wheel. Remove шплинты and ослабьте, but do not remove absolutely, корончатые a nut of spherical hairpins of both tips of draught. By means of a small stripper separate tips of connecting steering draught from a rotary fist and average draught.

Use вильчатого a divider of spherical hinges most likely will lead to damage of a cover of the hinge.


    Application двухзахватного of a stripper for a detachment of a tip of connecting steering draught from a rotary fist - pay attention that the nut has been only weakened, but not removed completely; it allows to avoid a spontaneous partition of components.
    If connecting draught demands replacement, count up quantity of the bared coils of a carving and write down result, for the purpose of observance of former convergence of forward wheels at assemblage. Loosen the a collar of a tube of a regulator also unscrew a draught tip.
    If the left tip of connecting steering draught is subject to replacement, count up and write down quantity of the bared coils of the carving which are sticking out of a tube of a regulator and a new tip roll taking into account this data.
    Grease a carving part of a tip of draught with greasing for chassis components. Screw a new tip in a tube of a regulator and, screwing in draught in a tube, adjust distance from last to a spherical hairpin, having left the same quantity of the bared coils of a carving that took place before dismantling (see the made record) (number of the bared coils from both parties of a regulator one should not differ from another more than on three). Do not tighten while collars of a tube of a regulator. For installation of assemblage of connecting steering draught insert a spherical hairpin of its left tip into a rotary fist, and a hairpin of the right tip - in average draught. Screw nuts and tighten them with demanded effort. If the spherical hairpin at a tightening of nuts is turned, knock down it in конусное an aperture by means of the big nippers. Establish new шплинты. In case of need tighten a nut a little more for combination of the nearest has spent on drink with an aperture under шплинт in a hairpin. Tighten nuts of collars of a tube of a regulator with demanded effort (Specifications to the Head of Adjustment and routine maintenance see). Drive away the car in a workshop on adjustment of corners of installation of forward wheels where corners will be checked up also in the correct image are modified.

Average steering draught

 PERFORMANCE ORDER

    Поддомкратьте redock of the car also establish it on props. Cock a lay brake. Loosen the, but do not remove, nuts of fastening of spherical hairpins of average bent for of connecting draught and to a rotary fist. Separate average draught from a rotary fist (see an illustration) and from connecting draught with the help двухзахватного a stripper, then remove nuts.
    For a detachment of average steering draught from connecting draught take advantage of a small stripper.
    Following the same technology, separate average draught from сошки the steering mechanism. If the left tip of average steering draught demands replacement, execute procedures of item 5 and 6 given Sections. Installation make upside-down. If any of spherical hairpins it starts to be turned at a tightening of a fixing nut, tyre out it in конусное an aperture by means of the big nippers. All fixture tighten with demanded effort.

Сошка the steering mechanism

Removal procedure сошки the steering mechanism look in Section Removal and installation of the steering mechanism.

Демпфер a steering drive

 PERFORMANCE ORDER

    Поддомкратьте redock of the car also establish it on props. Disconnect the helmsman демпфер from average draught, having taken advantage of a method described in item 2. Отболтите демпфер from a frame also remove it from the car. Installation make upside-down. Fixture демпфера tighten with demanded effort.