Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
The general information
Removal and installation of the forward stabilizer of cross-section stability and its plugs
Removal and installation of forward shock-absorbers
Removal and installation of a cross-section jet bar of a forward suspension bracket
Removal and installation of levers of a forward suspension bracket
Removal and installation of screw springs of a forward suspension bracket
Removal and installation of rotary fists
Replacement of spherical hinges
Removal and installation of a bar of the back stabilizer of cross-section stability
Removal and installation of back shock-absorbers
Removal and installation of a cross-section jet bar of a back suspension bracket
Removal and installation of levers of a back suspension bracket
Removal and installation of screw springs of a back suspension bracket
Removal and steering wheel installation
Condition check, removal and installation of a steering drive
Removal and installation of the steering mechanism
Removal and installation of the pump of system of hydrostrengthening of a wheel
Prorolling of system of hydrostrengthening of a wheel
Wheels and tyres - the general information
Corners of installation of forward wheels - the general information
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Removal and steering wheel installation
|
All considered models are equipped by a safety pillow. The pillow constantly is in "the guarded" condition and can work to (be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receptions as a result of a trauma) each time at carrying out of any works with components of system of safety disconnect a negative wire from the battery. After a detachment of a wire from the battery before starting to work wait still at least two minutes (the system is equipped by the condenser to which time for a discharge is required). More in detail about work of system of safety the System of an onboard electric equipment see the Head. |
|
Establish operated wheels of the car rectilinearly. Disconnect a negative wire from the battery.
|
If the audiosystem of your car is equipped by a security code before to disconnect a negative wire from the battery make sure that you have that for system input in action after end of works. |
Give four fixing nuts and disconnect the module of a pillow of safety from a steering column. Disunite an electric socket of the module. At work with the module always hold its open party from own body. Always put the module on a workbench or other surface the open party upwards (at all downwards!).
|
For removal of the module of a pillow of safety give the top nuts (right top nuts are occupied by the same position from a steering wheel opposite side).
|
|
… and the bottom nuts (the right is located similarly from an opposite side from a steering wheel).
|
|
Release lock uvulas and disunite an electric socket of the module of a pillow of safety.
|
Give a nut of fastening of a steering wheel, then mark position of a steering shaft under the relation to a nave (if such labels are not put not so or if they are not combined) for the purpose of simplification of the subsequent assemblage.
|
Do not suppose проворачивания a steering shaft after steering wheel removal.
|
|
Before steering wheel removal make sure of combination of adjusting labels on its nave and a pin of a shaft of a column (if those are available); if labels are absent, put them independently with the help чертилки or a white paint.
|
By means of a stripper remove a steering wheel from a shaft. At all it is not necessary to force down a wheel from a shaft a hammer.
|
Remove a steering wheel from a shaft only by means of a stripper AT ALL СБИВЙТЕ ITS HAMMER!
|
If position of operated wheels during procedure performance did not vary (they remained are directed rectilinearly), now it is possible to establish a steering wheel into place. If wheels turned, it is necessary to make centering of a spiral spring of a pillow of safety. For this purpose establish forward wheels strictly rectilinearly and rotate a rotor of an hour spring clockwise against the stop (it is not necessary to make too big efforts). Now turn a rotor on two and a half a turn counter-clockwise. In this position of a wire of a horn there should be above, and wires of the module of a pillow - below.
|
Details of an hour spring of a pillow of safety.
|
For installation of a steering wheel achieve combination of adjusting labels on its nave and a shaft pin. Establish a nut and tighten it with demanded effort.
Establish into place the module of a pillow of safety. Screw four fixing nuts and tighten them with demanded effort.
Connect a wire to the negative plug of the battery
|
|
|
|