Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
- Suspension bracket and steering
   The general information
   Removal and installation of the forward stabilizer of cross-section stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross-section jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross-section jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and steering wheel installation
   Condition check, removal and installation of a steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Prorolling of system of hydrostrengthening of a wheel
   Wheels and tyres - the general information
   Corners of installation of forward wheels - the general information
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7

Removal and installation of the pump of system of hydrostrengthening of a wheel

Components of the pump of system of hydrostrengthening of a wheel and its arms (engine V8).

Components of the pump of system of hydrostrengthening of a wheel and its arms (the 6-cylinder engine)


 PERFORMANCE ORDER

    Loosen the a tension drive a belt also remove a belt from a pump pulley (the Head of Adjustment and routine maintenance). By means of a syringe suck away from the tank of system of hydrostrengthening of a wheel of probably more liquid. Establish drain capacity under the pump and disconnect from it высоконапорную and returnable hydraulic lines. For access improvement to a hose of a returnable line probably it is required to remove an air cleaner casing (the Head of the Power supply system and release of the fulfilled gases). Закупорьте the open ends of lines in order to avoid leaks of a liquid and hit in dirt system.

Shtutsernye connections of tubes and hoses of hydraulic lines of the pump.

    Give forward fixing bolts both back fixing bolts and nuts, then remove the pump from the engine. In case of need removals from the pulley pump at first measure size выступания from its nave of a shaft of the pump. Remove a pulley from a shaft by means of a special stripper (for pulleys of pumps of systems of hydrostrengthening) - ask in shops of automobile accessories.

For removal of pulleys of pumps of system of hydrostrengthening of a wheel the stripper of such design is issued - ask in shops of automobile accessories.

    For landing of a pulley to a pump shaft the special tool, however from a long bolt, a nut, a washer and a replaceable face head of the same also is issued this time that the nave of a pulley of diameter can be independently made its equivalent. Pull a pulley on a shaft so that the shaft acted over its nave on the same size that before dismantle.
    For pulley putting on on a pump shaft the special tool, but … also is issued

… this time it can make replacement, taking for this purpose a long bolt with the same step of a carving, as a carving in an end face of a shaft of the pump, a nut, a washer and a replaceable face head of the same external diameter, as a shaft nave.

    Installation make upside-down. On termination of works do not forget to pump over system of hydrostrengthening of a wheel (Section Prorolling of system of hydrostrengthening of a wheel).