Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
- Brake system
   The general information
   System of antiblocking of brakes (ABS) - the general information
   Replacement колодок disk brake mechanisms
   Removal, major repairs and installation of a support of the disk brake mechanism
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms
   Removal, major repairs and installation of wheel cylinders
   Removal and installation of the combined valve (regulator)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake hoses and lines
   Prorolling of brake system
   Functioning check, removal and installation of the vacuum amplifier of brakes
   Functioning check, removal, installation and adjustment of the gauge-switch of stoplights
   Adjustment of a lay brake
   Replacement of cables of a drive of a lay brake
   Replacement of boots of a lay brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7


Adjustment of a lay brake

Models 1993 вып.

 PERFORMANCE ORDER

  1. Make sure that drums (or disks) brake mechanisms of back wheels rotate freely, without закусываний, then completely cock the lever of a lay brake.
  2. Поддомкратьте a back of the car also establish it on props.
  3. With chalk or fatty pencil mark position of an adjusting nut on the tip equipped with a carving натяжителя a cable.
  1. On models 1993 вып. With a chalk or a fatty pencil mark position of an adjusting nut (the left arrow) on the tip equipped with a carving натяжителя a cable, then screw a nut approximately on 13 mm more deeply on a tip; if carrying out of replacement of a back cable is planned, compress its clamp (the right arrows) small шланговым a collar of worm type.
  1. Screw a nut more deeply on a tip натяжителя approximately on 13 mm. If lengths of a carving part of a tip it appears insufficiently, replace натяжитель (Section Replacement of cables of a drive of a lay brake). It is not necessary to try to improve натяжитель or to use it repeatedly.
  2. Release the lever of a lay brake and make sure that back wheels rotate freely.
  3. Clean jacks and lower the car.
  4. Check up functioning of brakes on a bias.

Models since 1994 вып.

 PERFORMANCE ORDER

  1. Make sure that drums (or disks) brake mechanisms of back wheels rotate freely, without закусываний, then completely cock the lever of a lay brake.
  2. Поддомкратьте a back of the car also establish it on props.
  3. Put on a rod натяжителя a label approximately in 6,5 mm from an arm натяжителя.
  1. On models 1994 and 1995 вып. Put on a rod натяжителя a label on distance approximately 6.5 mm from an arm.
  1. Tighten an adjusting nut on the balance weight so that the label on a rod натяжителя was combined with its arm.

On any of the reasons do not tighten and do not weaken an adjusting nut натяжителя after adjustment end!

  1. Release the lever of a lay brake and make sure that back wheels of the car rotate freely.
  2. Clean jacks and lower the car.
  3. Check up functioning of brakes on a bias.