Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
- Brake system
The general information
System of antiblocking of brakes (ABS) - the general information
Replacement колодок disk brake mechanisms
Removal, major repairs and installation of a support of the disk brake mechanism
Condition check, removal and installation of a brake disk
Replacement of boots of drum-type brake mechanisms
Removal, major repairs and installation of wheel cylinders
Removal and installation of the combined valve (regulator)
Removal and installation of the main brake cylinder
Check of a condition and replacement of brake hoses and lines
Prorolling of brake system
Functioning check, removal and installation of the vacuum amplifier of brakes
Functioning check, removal, installation and adjustment of the gauge-switch of stoplights
Adjustment of a lay brake
Replacement of cables of a drive of a lay brake
Replacement of boots of a lay brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Replacement of boots of a lay brake (disk brake mechanisms of back wheels)
|
|
Loosen the hooks of fastening of wheels, release a lay brake, поддомкратьте a back of the car and establish it on props. Block wedges forward wheels in avoidance откатывания the car.
Remove back wheels.
Cut off lock washers and remove a brake disk (see an illustration).
|
|
If the drum does not act in film freely with башмачной assemblages, make sure that the lay brake is completely released, then impregnate with getting oil a joint between a nave and a drum and repeat attempt. If the drum on the former does not act in film, it is necessary to take away boots from its walls. It is made by extraction of a stopper from a board of the brake mechanism. Then a narrow screw-driver take away the lever from an adjusting castor and the second screw-driver rotate a castor, taking away boots from drum walls. Now the drum should act in film freely |
|
|
|
Take a stopper from a board of the brake mechanism and pass in opened aperture the tool for adjustment of brakes.
|
|
|
|
… press the tool to the top part of an adjusting castor and start to rotate the last downwards (clockwise if to look at the car behind), taking away thereby boots of a lay brake from walls of a nave of a disk (which in a picture it is for descriptive reasons already removed).
|
Check of a condition and replacement of boots of a lay brake make according to illustrations more low. Observe the recommended order of performance of procedures and attentively study explanatory notes to pictures.
|
|
All four boots of a lay brake should be replaced simultaneously, however in avoidance перепутывания components make works from each of assemblages serially. |
|
|
Fingers having pushed out a clamp from a brake board, hook a forward keeping clip, having released it; take a finger and lay it together with a clip in a polyethylene package, having excluded thereby danger to lose small components.
|
|
|
Operating similarly, remove a back keeping clip and a finger.
|
|
|
Disconnect the bottom spring from boots of a lay brake.
|
|
|
Disconnect the top spring from a back boot of a lay brake.
|
|
|
Remove both boots of a lay brake.
|
|
|
In a picture the assemblage scheme together boots, springs and a regulator is presented.
|
|
|
Having compressed new boots together by means of the top spring, establish them on assemblage.
|
|
|
Dissolve the top ends of boots and hook on them for a support as is shown in a picture.
|
|
|
Establish into place a regulator.
|
|
|
Make sure that the regulator is hooked for boots as it is shown in a picture.
|
|
|
Establish the bottom spring.
|
|
|
Make sure that coils of the bottom spring are turned downwards - from a regulator as it is shown in a picture.
|
|
|
Establish a back finger and keeping clip as shown; the finger head should sit down densely in the bottom, smaller part of an aperture in a clip.
|
|
|
In the similar image establish a forward finger and keeping clip.
|
Before installation to the place of a disk check up working surfaces of its nave on presence of cracks, scratches, furrows and overheat stains. If any from listed above defects cannot be removed by means of an emery paper (№ 180), the disk should be replaced.
After installation of new boots of a lay brake establish into place brake disks. Do not forget to establish on hairpins new lock washers of fixing of disks.
Take from brake boards rubber stoppers, pass in the aperture which has opened in a board the adjusting tool and, rotating a gear castor, achieve easy прихватывания a disk at its rotation (illustrations "see Take a stopper from a board of the brake mechanism..." And "… press the tool to the top part of an adjusting castor..."). Now turn a castor in the opposite direction, before disk clearing - keep thus a screw-driver the regulator lever taken away from a castor. Repeat procedure of adjustment for the brake mechanism of an opposite wheel. Establish to the place of a stopper of brake boards.
Put on wheels, screw nuts of their fastening and lower the car on the earth. Tighten nuts of fastening of wheels with demanded effort (Specifications to the Head of Adjustment and routine maintenance see).
For definitive self-regulation of brake mechanisms make a number of braking at movement of the car both back, and a forward course.
Before starting car operation make sure of serviceability of functioning of brake system.
|
