Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
- Brake system
The general information
System of antiblocking of brakes (ABS) - the general information
Replacement колодок disk brake mechanisms
Removal, major repairs and installation of a support of the disk brake mechanism
Condition check, removal and installation of a brake disk
Replacement of boots of drum-type brake mechanisms
Removal, major repairs and installation of wheel cylinders
Removal and installation of the combined valve (regulator)
Removal and installation of the main brake cylinder
Check of a condition and replacement of brake hoses and lines
Prorolling of brake system
Functioning check, removal and installation of the vacuum amplifier of brakes
Functioning check, removal, installation and adjustment of the gauge-switch of stoplights
Adjustment of a lay brake
Replacement of cables of a drive of a lay brake
Replacement of boots of a lay brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Removal, major repairs and installation of a support of the disk brake mechanism
|
The dust developed by brake mechanisms in the course of their work can contain unhealthy asbestos. At all do not blow off a dust from surfaces of components of brake mechanisms the compressed air and do not inhale it. Works is better to make in a protective respiratory mask. At all do not use for cleaning of components of brake mechanisms solvents on an oil basis or gasolines - use only патентованными means for cleaning of brakes! |
|
If there is a necessity for carrying out of major repairs of a support (usually in a consequence of presence of leaks of a liquid), before starting to work study all possible variants of its performance. It is possible to get on an exchange basis фабрично the restored supports that appreciably simplifies a problem. If the decision on restoration of an old support is made before to begin work make sure available special ремнабора. Supports always are under repair in pairs - major repairs carrying out only one of them is not admissible at all! |
Removal
|
Uncover the tank of a brake liquid. Suck away (not a mouth) from the tank of two third of its contents. Merge a liquid in the container for its subsequent delivery in special place of acceptance.
Loosen the nuts of fastening of forward wheels, поддомкратьте redock of the car also establish it on props. Remove forward wheels.
Drown the support piston in the nest (the picture see).
|
If be going to remove only a support (and not to make its major repairs), do not disconnect from it a brake hose. Give a hollow bolt reception штуцерного knot of a brake hose and disconnect a hose from a support (see an illustration). Near at hand it is necessary to have rags for gathering of a spilt liquid. Wrap up the end of a hose a polyethylene film and fix its rubber bandage (or закупорьте a hose) in order to avoid excessive losses of a liquid and hit in dirt system. |
Give two fixing bolts remove a support from the car (Section Replacement колодок disk brake mechanisms). If the support acts in film for the purpose of providing of access to other components, tie up it aside to a suspension bracket element - watch, that the brake hose thus did not stretch!
|
|
Major repairs
|
Wipe an external surface of a support a special cleaner or a pure brake liquid. At all do not use gasoline, kerosene or solvents on an oil basis! Lay a support on a pure workbench.
Enclose in a support as a pillow wooden брусок or some lumps of rags and squeeze out the piston of the support cylinder the compressed air. It is not necessary to increase air giving more than it is necessary for piston squeezing. At too strong pressure the piston, having jumped out it can be damaged, without looking at all at the enclosed pillow.
|
At all do not thrust fingers in space in front of the piston at blowing of last of the cylinder is it is fraught with reception of a serious trauma. |
|
Having enclosed under an obverse surface of the piston of a support an amortisation pillow (wooden брусок or rags), squeeze out the piston of the cylinder the compressed air - watch that fingers have not got between the piston and a frame of a support (pillow)!
|
Cautiously take duster from a support nest.
|
Cautiously take duster from a support.
|
|
Components of a support of the disk brake mechanism.
|
By means of the wooden or plastic tool take a cuff from a flute in a nest of a support Use of metal tools can lead to damage of a mirror of a nest.
|
The piston cuff should be taken from a nest by means of the wooden or plastic tool in order to avoid damage of a mirror of a nest and-or a cuff flute - it is convenient to take advantage for this purpose of a pencil.
|
Turn out the gate of prorolling of a support, then remove and throw out plugs of fixing pins. Remember that rubber components are not subject to the repeated use.
|
Grasp edges of plugs under installation of fixing pins by nippers and, making vrashchatelno-progress by a hand, take them from support eyes.
|
Wash out the remained components in патентованном a cleaner or a pure brake liquid, then dry their compressed air.
Carefully check up the piston on presence задиров, agnails or infringements of an external covering. In case of revealing of defects of a surface the component is subject to replacement.
To similar check subject a mirror of a nest of the piston in a support. Insignificant defects can be eliminated by means of polishing by a thin emery paper. The fixing pins of a support defective or damaged by corrosion are subject to replacement.
|
|
Installation
|
At assemblage grease a mirror of a nest and a cuff of the piston with a pure brake liquid. Establish a cuff in a flute in a nest.
Grease the piston with a pure brake liquid, then fill it perpendicularly and knock down against the stop in a nest bottom.
|
At installation of the piston a support before утапливать it in a nest make sure that it is not warped.
|
Fill new duster in a flute on the piston, then accurately plant it in a nest.
|
If there is no possibility of application of the special tool for landing dusterа in a support nest, it is possible accurately обстучать it on all perimetre выколоткой.
|
Screw the prorolling gate.
Establish internal and external plugs of pins of fastening of a support
Check up fixing pins on presence of signs of excessive corrosion, in case of need make replacement.
Clear and grease plugs of fixing pins of a support (illustrations "see Take plugs of both fixing pins..." And "Establish plugs into place").
Establish a support.
Connect a brake hose and tighten a hollow bolt of its fastening to a support, having laid new copper washers. Tighten a bolt with demanded effort.
If the brake line undocked, do not forget to pump over a brake (Section Prorolling of brake system).
Establish wheels and lower the car on the earth. Tighten nuts of fastening of wheels with demanded effort.
On termination of work some times strongly squeeze out a pedal of a brake for усадки колодок on a disk.
Before starting car operation check up serviceability of functioning of brakes.
|
|
|
|