Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
- Coupling and трансмиссионная a line
The general information
Coupling - the general description and check of serviceability of functioning
Removal and installation of components of hydraulic system of deenergizing of coupling
Removal, check of a condition and installation of components of coupling
Removal, check of a condition and installation выжимного the coupling bearing
Check of a condition and replacement of the directing bearing
Kardannye shaft, differentials and bridges - the general information
Condition check трансмиссионной lines
Removal and installation карданных shaft
Replacement карданных hinges
Replacement of an epiploon of a shaft of a leading gear wheel of differential
Removal, service and installation of a nave and bearings (forward wheel)
Removal, major repairs and installation of a forward power shaft
Removal and installation of assemblage of the forward bridge
Removal and installation of a back semiaxis and bearing assemblage
Removal and installation of assemblage of the back bridge
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Removal and installation карданных shaft
|
|
Disconnect a negative wire from the battery.
Поддомкратьте the car also establish it on props. Establish transmission in neutral position at the released lay brake.
|
|
Back карданный a shaft
Removal
|
|
For the purpose of balancing preservation карданный the shaft should be established into place in former position. Чертилкой, a white paint or кернером put labels of relative position of the case of a shaft and its holder крестовины a shaft of a leading gear wheel of differential.
|
|
Before removing bolts and collars of fastening of the back end карданного a shaft to back differential accurately mark mutual position of two holders крестовины карданного the hinge.
|
Remove bolts and collars back карданного the hinge. For maintenance of optimum access to bogs turn in appropriate way a shaft (or back wheels).
|
|
For prevention проворачивания карданного a shaft during easing of bolts of a flange, pass a screw-driver through the holder крестовины, as is shown in a picture.
|
Attach covers of needle bearings to крестовине a sticky tape in order to avoid their loss in the course of removal.
Lower a back part карданного a shaft and take its forward part from transmission or a distributing box.
In order to avoid losses of a liquid and pollution of internal components removed карданного a shaft, wrap up картер transmission or a distributing box a polyethylene package, having fixed its rubber bandage.
|
|
Installation
|
|
Each time at installation карданного a shaft into place it is necessary to use new collars of holders крестовин. |
|
|
Remove a polyethylene package from transmission or a distributing box and absolutely wipe a surface of last. Carefully check up an epiploon condition. If the epiploon is worn out, replace it (the Head Automatic transmission).
Enter a forward part карданного a shaft into transmission (2WD) or a distributing box (4WD).
Lift a back part карданного a shaft in adjusting position, having tracked combination of adjusting labels. If labels do not coincide, turn back wheels, having achieved combination of labels of a flange of a leading gear wheel and карданного a shaft.
Remove a sticky tape, крепящую covers of bearings and establish new collars and bolts. Tighten bolts with demanded effort.
|
|
Forward карданный a shaft (models 4WD)
|
|
By means of a paint, a chalk, a marker or чертилки mark position forward карданного the hinge (model 1993 and 1994 вып.) or the CV-hinge (model 1995 вып. With карданным shaft of the Third type) in relation to the holder крестовины a shaft of a leading gear wheel of forward differential. Also mark position карданного a shaft in relation to a distributing box.
|
|
Before starting a detachment карданного the hinge from the holder крестовины a shaft of a leading gear wheel of differential of the forward bridge on models 1993 and 1994 вып. Mark hinge position in relation to the holder (as is shown in a picture); before a detachment of the CV-hinge from the holder крестовины a shaft of a leading gear wheel of forward differential of models 1995 вып. Mark its position in relation to the holder (as shown).
|
|
|
Before a detachment карданного the hinge from a connecting flange of a distributing box make marks of their mutual position.
|
Отболтите the forward end карданного a shaft from the holder крестовины a shaft of a leading gear wheel of differential, and the back end - from a connecting flange of a distributing box (see an illustration) and remove a shaft from the car. On models 1993 and 1994 вып. In order to avoid loss of covers attach them to крестовине a sticky tape.
Installation make upside-down. If you make replacement карданного a shaft of the Third type on model 1995 вып., do not forget to make adjusting measurements. All fixture tighten with demanded effort.
Clean jacks and lower the car on the earth.
Connect a wire to the negative plug of the battery
|
|
Adjustment карданного a shaft of the Third type (some of models 1995 вып.)
|
|
At installation new карданного a shaft of the Third type before starting car operation it is necessary to make its measurements and adjustment. |
|
|
Measure distance from a cover of the CV-hinge to a cut of its protective cover.
| |
If you have established new карданный a shaft of the Third type on model 1995 вып., this distance should be measured and adjusted before car operation.
|
|
|
The given measurement should be made at installation new карданного a shaft and at not loaded car. Compare results of measurements to requirements of Specifications. |
In case of need make adjustment карданного a shaft, having weakened a counternut and having shifted one end of a shaft to the CV-hinge or from it, achieving the demanded size of a backlash between a cover of the hinge and a cut of its protective cover. Then tighten a counternut with demanded effort.
|
|
|
|
