Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
- Coupling and трансмиссионная a line
   The general information
   Coupling - the general description and check of serviceability of functioning
   Removal and installation of components of hydraulic system of deenergizing of coupling
   Removal, check of a condition and installation of components of coupling
   Removal, check of a condition and installation выжимного the coupling bearing
   Check of a condition and replacement of the directing bearing
   Kardannye shaft, differentials and bridges - the general information
   Condition check трансмиссионной lines
   Removal and installation карданных shaft
   Replacement карданных hinges
   Replacement of an epiploon of a shaft of a leading gear wheel of differential
   Removal, service and installation of a nave and bearings (forward wheel)
   Removal, major repairs and installation of a forward power shaft
   Removal and installation of assemblage of the forward bridge
   Removal and installation of a back semiaxis and bearing assemblage
   Removal and installation of assemblage of the back bridge
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7 Куда сходить с ребенком в Санкт-Петербурге Афиша


Removal and installation of a back semiaxis and bearing assemblage

Removal

 PERFORMANCE ORDER

  1. Loosen the nuts of fastening of a wheel, поддомкратьте a back of the car also establish it on props. Remove a wheel.
  2. Remove a brake drum, then give nuts of fastening of a board of the brake mechanism.
  1. Отболите four nuts of fastening of a board of the brake mechanism using a head with the extension piece through an aperture in a wheel nave.
  1. Connect a hammer with sliding brisk and a nozzle to a flange of a semiaxis and take last from a bridge sleeve.
  1. Take полуось from a sleeve of the bridge by means of a hammer with sliding brisk and nozzles on an axis flange.
  1. If the bearing is subject to replacement, deliver assemblage in a workshop of car-care centre or dealer branch for removal of the old bearing and запрессовки on its new. At installation of the new bearing take care also of replacement of an external epiploon of a semiaxis (the following point see).
  2. If on a board of the brake mechanism there are traces of leaks of greasing of differential, it is necessary to replace an external epiploon of a semiaxis. Remove an old epiploon by means of a hammer with sliding brisk and a stripper in internal captures. A new epiploon plant by means of the special tool or a piece of a pipe of suitable diameter.
  1. Take an epiploon of a semiaxis from a sleeve of the bridge by means of a hammer with sliding brisk with the stripper attached to it with internal captures.
  1. Grease epiploon sponges, then fill an epiploon on the place by means of the special tool or the pipe piece which external diameter will be slightly less than external diameter of an epiploon.

Installation

 PERFORMANCE ORDER

  1. Wipe a bearing nest in a bridge sleeve. Fill the bearing special (for wheel bearings) greasing, put also a thin layer of greasing on an external surface of the bearing.
  2. Grease sponges of an internal epiploon, then fill полуось in a bridge sleeve, trying to hold it it is coaxial with the last not to damage an epiploon.
  3. Establish nuts of a board of the brake mechanism, strongly tighten them. Put on a brake drum a bridge flange.
  4. Establish a wheel and strongly tighten nuts of its fastening. Lower the car on the earth and tighten nuts of fastening of a wheel with demanded effort (Specifications to the Head of Adjustment and routine maintenance see).