Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
- Рядный the six-cylinder engine
   The general information
   The repair procedures, which performance it is possible without extraction of the engine from the car
   Reduction in position ВМТ of a step of compression of the piston of the first cylinder
   Removal and installation of a cover of a head of cylinders
   Removal, check of a condition and installation коромысел and bars of pushers
   Replacement клапанных springs, their plates and маслоотражательных caps
   Removal and installation of the inlet pipeline / a final collector
   Removal and installation of a head of cylinders
   Replacement of a forward epiploon of a cranked shaft
   Condition check, removal and installation of a cover of a distributive chain, chain and its asterisks
   Removal, check of a condition and installation of a camshaft, bearings and hydraulic pushers
   Removal and pallet installation картера
   Removal, check of a condition and installation of the oil pump
   Removal and installation of a flywheel/privodnogo of a disk
   Replacement of a back epiploon коленвала
   Check of a condition and replacement of rubber pillows of support of the engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions


e65f60b7

Replacement of a back epiploon коленвала

 PERFORMANCE ORDER

    Remove the pallet картера (Has undressed Removal and pallet installation картера). Uncover the back radical bearing and take from it an epiploon half, having hooked its small screw-driver. Cautiously fill one party of the second (top) half of radical epiploon in the flute by means of small brass выколотки and a hammer. Thus its second end should be put out over a block surface so that it became possible to grasp it flat-nose pliers. Observe extreme care, trying not to admit damage of a pin of a cranked shaft.
    Fill in a flute in the block one of the ends of the top half of back radical epiploon...

... So that its second end was put forward from the block so that there was a possibility to grasp it nippers.

    Carefully smooth out surfaces of a cover of the radical bearing and a back part of the block/kartera of the engine, having removed with all of them traces of oil and old hermetic. Grease sponges of the top half of new epiploon with pure impellent oil, and its external surface - liquid soap.

Installation of a back epiploon коленвала.

    Insert an epiploon into a flute in the block sponges forward. Grease both end faces of the bottom half of epiploon with hermetic RTV and moisten an external surface with liquid soap (see an illustration above). Do not suppose hit of hermetic and soap on epiploon sponges. Fill an epiploon in a cover of the radical bearing and grease its sponges with impellent oil.

Do not put at the given stage hermetic on interfaced surfaces of the block and a cover of the radical bearing. It is made after measurement of backlashes in bearings of a cranked shaft.

    Grease edges with the removed facets of a cover of the back radical bearing hermetic for fixing of carving connections (Locktite 518 or its equivalent). Also establish a cover into place. Tighten fixing bolts with demanded effort.
    Put a small amount of hermetic for fixing of carving connections on the areas of a surface of a cover of the back radical bearing shaded on drawings before its installation on the engine.
    Installation of the remained components make in an order, the return to an order of their removal. Fill in in the engine demanded quantity of impellent oil (the Head of Adjustment and routine maintenance), start the engine and check up it on oil leaks.