Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
- Body
   The general information
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Service of loops and locks
   Replacement wind and motionless glasses
   Removal, installation and adjustment of position of a cowl
   Removal and installation of the lock of a cowl and cable of its drive
   Removal and installation to the place of the panel of a decorative lattice of a radiator
   Removal and installation of a forward wing
   Removal and installation of bumpers
   Removal and installation of the panel of an internal upholstery of a door
   Removal, installation and adjustment of position of a door
   Removal and installation of handles, the cylinder and clamp (latch) of the lock of a door
   Removal and installation of a windowpane of a door
   Removal and installation of a regulator of a window of a door
   Removal and installation of the central console
   Removal and installation of the panel of an upholstery of a door of a back
   Removal, installation and adjustment of position of a door of a back
   Replacement of an emphasis of a door of a back
   Removal and installation of facing of a combination of devices
   Removal and installation of facings of a control panel
   Removal and control panel installation
   Removal and installation of covers of a casing of a steering column
   Removal and installation of rear-view mirrors
   Remove also lattice installation обтекателя
   Removal and installation of seats
   Control кузовные the sizes
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7

Removal and installation of handles, the cylinder and clamp (latch) of the lock of a door

Door latch

 PERFORMANCE ORDER

    Completely lift glass of a window and remove the panel of an internal upholstery of a door and a water filter (Has undressed Removal and installation of the panel of an internal upholstery of a door). Disconnect rods of draughts from a latch.
    Turn a plastic clamp upwards and disconnect rods of draughts of a latch.
    Give three fixing screws with heads of type TORX. Probably, for страгивания screws the shock screw-driver is required.
    Give a bolt of fastening of a latch.
    Remove a latch from a door. Put a latch on an adjusting place and screw fixing bolts. Strongly tighten bolts. Connect to a latch rods of draughts. Make sure of adequacy of lock-out of a door. In case of need make adjustment of position of a latch (having weakened for this purpose bolts), achieving ease защелкивания a door (the door handle thus should appear заподлицо with a door surface). After installation end ослабьте the adjusting screw of draught, having passed a key-shestigrannik of 5/32 inches (4,0 mm) in an access aperture in a door end face. Loosen the the adjusting screw also push it upwards on a cut for a choice of a weak point of draught, then tighten the screw.
    Pass a key-shestigrannik a head in an adjusting aperture, ослабьте the screw and advance it upwards on a cut for sample of a weak point of draught.

The lock cylinder

 PERFORMANCE ORDER

    Remove the external handle of a door. Disconnect draught, having taken advantage of a screw-driver for pushing out of the holder and extraction of the cylinder of the lock from a door. Installation make upside-down.

The external handle

 PERFORMANCE ORDER

    Disconnect draught of the external handle (a remote drive) doors from a lock latch, give fixing nuts and remove the handle from a door.
    Details of installation of the external handle and the cylinder of the lock of a door.
    Establish the handle into place, connect draught and screw nuts. Strongly tighten nuts.

The internal handle

 PERFORMANCE ORDER

    Give a fixing bolt, turn the handle forward and disconnect draughts, then remove the handle from a door.
    Give a bolt (arrow), turn the internal handle forward and disconnect rods of draughts.