Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
- The power supply system and release of the fulfilled gases
   The general information
   Procedure of dump of pressure of fuel
   Check of pressure of fuel and functioning of the fuel pump
   Removal and installation of a fuel tank
   Cleaning and repair of a fuel tank - the general information
   Repair and replacement of fuel lines
   Removal and installation of the fuel pump
   Check of serviceability and replacement of the block of the gauge of level of fuel
   Removal and installation of assemblage of an air cleaner
   Replacement of a cable of gas
   System of injection of fuel - the general information
   Check of serviceability of system of injection of fuel
   Serviceability check, removal and installation of the case of a throttle
   Check of serviceability and replacement of a regulator of pressure of fuel
   Serviceability check, removal and installation of injectors of fuel
   Check of functioning and replacement of components of system of stabilisation of turns of idling (IAC)
   Service of system of release of the fulfilled gases - the general information
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7

Service of system of release of the fulfilled gases - the general information

Check of a condition and repair of components of system of release should be made after a sufficient time interval after engine deenergizing when system components have completely cooled down. Besides, working under the car take care of reliability of its fastening in the lifted condition.

The release system consists of a final collector (ов), каталитического the converter, the muffler, final and connecting pipes, arms, подвесов and fixing collars and clips. System components fasten to the bottom of the car by means of arms and rubber подвесов. Wrong installation of any details conducts to occurrence of extraneous noise and the vibrations transferred on a body of the car.

The arm of an exhaust pipe fastens to the bottom of the car by means of rubber подвеса.

The muffler and pipes

For поддерживания components of system of release constantly in a satisfactory condition and for the purpose of prevention of occurrence of noise and vibrations regularly check a condition of its components. Examine components on presence of damages, the deformations, the dispersed seams, holes, ослабшего fixture, signs of excessive corrosion and other defects as a result of which presence there can be a leak of the fulfilled gases and their hit in car salon. The spoilt sections of system of release should not to try be restored - they should be replaced. Do not forget also about condition check каталитического the converter.

If sections of system as a result of corrosion influence do not give in to a partition, for their removal application of the welding equipment can be demanded. The most simple way of the decision of the given problem is the reference behind the help in a car-care centre workshop where sections will be divided by means of gas cutting. However, in case of the constrained monetary circumstances (or for the purpose of self-satisfaction reception) it is possible to try to make removal of defective components independently. For this purpose (if there is no possibility to take advantage of gas cutting) it is possible to dismember system sections with the help ножовки on metal. If there is an access to a source of compressed air and there is a possibility to take advantage of a pneumatic cutting/cutting nozzle, take advantage of it. Do not forget to put on goggles and work in gloves.

At performance of repair of system of release it is necessary to adhere to following elementary rules:

    Move ahead along system from its end to the beginning. For simplification отдавания fixture preliminary impregnate with its getting oil At installation of components of system necessarily replace linings, подвесы and collars. Carving part of fixture before installation grease with antitaking hermetic. Make sure that between again established components of system and a surface of the bottom of the car there is the sufficient backlash necessary for prevention of damage of internal furnish of salon, rugs and изоляционного a layer as a result of an overheat. Special attention give to quality of installation каталитического the converter and a thermofilter.

The Katalitichesky converter

The Katalitichesky converter during engine work heats up to very heats. Before touching it make sure that it has enough cooled down.


More detailed information on a design and an action principle каталитического the converter is resulted in the Head of System of decrease in toxicity of the fulfilled gases and engine management.

Regularly check a thermofilter on presence of cracks, dents, easings of fastening or fixture loss.

 PERFORMANCE ORDER

    Remove a thermofilter and check up каталитический the converter on presence of cracks and other damages. If каталитический it is necessary to replace the converter, give nuts of fastening of its both flanges, remove rubber support and take the converter from system of release of the fulfilled gases (for removal of the converter from fixing hairpins it is required to push away sections of pipes of system). Installation make upside-down. Do not forget to replace a lining.