Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
- Systems of cooling, heating and air conditioning
   The general information
   Antifreeze - the general information
   Check of functioning and thermostat replacement
   Check of serviceability and replacement of the fan of system of cooling and муфты its couplings
   Check of functioning and replacement of the block of the gauge of temperature of a cooler
   Removal and installation of a radiator and broad tank of system of cooling
   Check of functioning of the water pump
   Removal and installation of the water pump
   Check of serviceability of an electric contour and replacement of components of the motor of the fan of a heater and air conditioner
   Removal and installation of the block of the fan of a heater
   Removal and installation of assemblage of management by a heater and air conditioner
   Removal and installation of the heat exchanger of a heater
   Check of serviceability and service of systems of heating and air conditioning
   Diagnostics of system of automatic control in temperature (automatic telephone exchange) without its removal from the car
   Removal and installation of the accumulator (store) of a central air of air
   Removal and installation of the compressor of a central air of air
   Removal and installation of the condenser of a central air of air
   Removal and installation of a tube of the calibrated jet
   Removal and installation of the evaporator of a central air
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7


Removal and installation of a radiator and broad tank of system of cooling

Before starting procedure performance wait full cooling of the engine.


 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Empty cooling system (the Head of Adjustment and routine maintenance). If the cooler is rather new, or is in a satisfactory condition, keep it for the further application.

Removal and installation of a broad tank of system of cooling

Before starting procedure performance wait full cooling of the engine.


 PERFORMANCE ORDER

  1. Uncover a jellied mouth of a tank and empty cooling system (the Head of Adjustment and routine maintenance), plums from a tank all liquid.
  2. Loosen the шланговые collars also disconnect a hose from a tank.
  3. Give screws/nuts and remove a tank.
  1. Give the screw with a nut, disconnect a hose (arrows) and take a broad tank of system of cooling from the engine.
  1. Installation make upside-down.

Radiator removal

 PERFORMANCE ORDER

  1. Loosen the шланговые collars remove from the unions радиаторные hoses. If hoses "have become attached", grasp them more close by the end self-blocked nippers and try повращать, then remove them from unions - try not to damage unions the Old or destroyed hoses it is necessary to cut off from unions and at assemblage to replace new.
  2. Disconnect a hose of a broad tank from a jellied mouth of a radiator.
  3. Take (having hooked them) two clips of fastening of forward rubber consolidation of a cowl, having provided with that access to two of bolts of fastening of the top support of a radiator (the panel with fixed on it information шильдами). Give bolts.
  4. Give other bolts of fastening of a support of a radiator and remove a support together with a clamp of the lock of a cowl and connected to it приводным a cable. Will put a support aside.
  1. Remove a radiator support together in a clamp of the lock of a cowl and will put it aside.
  1. Give screws of fastening of a casing of the fan to a radiator and shift a casing towards the engine.
  2. If the car is equipped АТ, disconnect from a back part of a radiator of a line of cooling трансмиссионной liquids (the Head Automatic transmission). For gathering of a spilt liquid take advantage of drain capacity.
  3. Закупорьте lines and unions.
  4. Give fixing bolts and cautiously take a radiator from an impellent compartment. Do not suppose pouring out from a cooler radiator on the painted surfaces of the car (antifreeze is aggressive in relation to them).
  1. Taking a radiator from an impellent compartment, try not to damage its plate about blades and a casing of the fan (arrow).

Radiator installation

After removal the radiator can be checked up on presence of signs of leaks and damages. If the radiator requires under repair, it it is necessary to send in a specialised workshop or the dealer branch, having in the order the corresponding equipment.

Taking a radiator from the car it is necessary to remember an arrangement and an order of installation of various rubber pillows and sealants (top, bottom and lateral). At assemblage all of them should be established in accuracy on the former places.

Rubber уплотнители and the pillows established on perimetre of a radiator and between a radiator and the condenser should be established at assemblage in accuracy on the former places.

Remains of insects and old leaves can be removed from backlashes between plates of a radiator by means of a soft brush or compressed air. Try not to bend a plate and not to cut about them fingers. At a radiator purge direct a current of air only to the opposite party from the engine.

 PERFORMANCE ORDER

  1. Check up radiator support on presence of signs of ageing of a material of rubber pillows and track, that in them it has been forgotten nothing at radiator installation into place.
  2. Installation make upside-down.
  3. After installation fill system of cooling with a mix of demanded structure (see the Head of Adjustment and routine maintenance).
  4. Start the engine and make sure of absence of signs of leaks of a cooler. Allow to the engine to get warm to normal working temperature that proves to be true a warming up of the top hose of a radiator. Again check up cooler level, in case of need make having added.
  5. If works are made on equipped АТ the car, check up also level трансмиссионной liquids, in case of need make having added.