Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
- Procedure of the general and engine major repairs
The general information
Engine major repairs - the general information
Check компрессионного pressure in cylinders
The diagnostic checks made by means of the vacuum gauge
Methods of removal of the engine and necessary safety measures
Removal and engine installation
Variants of restoration of the engine
Order of dismantling of the engine
Dismantling of a head of cylinders
Cleaning and check of a condition of a head of cylinders
Service of valves
Assemblage of a head of cylinders
Removal of shatunno-piston assemblages
Removal of a cranked shaft
Cleaning of the block of the engine
Check of a condition of the block of the engine
Хонингование cylinders
Check of a condition of shatunno-piston assemblages
Check of a condition of a cranked shaft
Check of a condition radical and шатунных bearings
Assembly order of the engine after end of its major repairs
Installation of a cranked shaft and check of backlashes of radical bearings
Installation of piston rings
Installation of shatunno-piston assemblages and check of backlashes in шатунных bearings
The first start of the engine after major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Removal of a cranked shaft
|
Extraction of a cranked shaft can be made only after the engine will be removed from the car. It is supposed also that a flywheel/privodnoj a disk, демпфер крутильных fluctuations, the distributive chain, the pallet картера, the oil pump and shatunno-piston assemblages are already removed from the engine. |
|
Before starting extraction of a cranked shaft measure its size axial люфта. Fix циферблатный a measuring instrument плунжерного type on the block so that its rod has appeared located coaxially with shaft and only touched a cheek of one of cranks (or to an end face of a pin of a shaft).
|
Definition axial люфта a cranked shaft with the help циферблатного a measuring instrument плунжерного type.
|
Take away a shaft against the stop back and null a measuring instrument. Then push a shaft against the stop forward and consider an instrument reading. The measured moving of a shaft corresponds to its size axial люфта. If люфт exceeds admissible value, check up persistent surfaces of a shaft on presence of signs of deterioration. If obvious signs of deterioration are not present, installation of new persistent bearings should help to correct a situation.
At absence available циферблатного a measuring instrument it is possible to take advantage probeом лезвийного type. Cautiously take away a shaft in one of the parties against the stop. Fill probeами a backlash between shaft and a forward surface of the persistent radical bearing. The total thickness probeов will be equal to size axial люфта a shaft.
|
Measurement of size axial люфта a cranked shaft with the help probeа лезвийного type.
|
Check up covers of radical bearings of a cranked shaft on presence of identification labels. Covers should be consistently numbered as their installation from a forward part of the engine to the back. If marks are absent, put it independently with the help кернера. Covers of radical bearings are often equipped by the arrow cast on their top part specifying a direction forward on the engine. Loosen the bolts of covers of radical bearings on 1/4 turns for one approach until there will be an untwisting possibility their hands. If hairpins are applied to fastening any of covers, remember their site that at assemblage to establish on former places.
|
Covers of radical bearings are usually numbered in front back on the engine (marksman) - on engines V8 in volume of number of 5.2 l are located on the passenger party of covers.
|
Cautiously обстучите covers a hammer with soft brisk, then separate them from the block. In case of need take advantage of bolts as points of support for removal of covers by means of the lever. Try not to drop loose leaves if they act in film together with covers.
Cautiously take a cranked shaft from the engine. It is reasonable to resort here to the help of the assistant - the shaft is heavy enough. Having left loose leaves on the places in the block and covers, establish covers of radical bearings on the former places and by hand tighten fixing bolts.
|
|
|
|