Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
- Рядный the six-cylinder engine
The general information
The repair procedures, which performance it is possible without extraction of the engine from the car
Reduction in position ВМТ of a step of compression of the piston of the first cylinder
Removal and installation of a cover of a head of cylinders
Removal, check of a condition and installation коромысел and bars of pushers
Replacement клапанных springs, their plates and маслоотражательных caps
Removal and installation of the inlet pipeline / a final collector
Removal and installation of a head of cylinders
Replacement of a forward epiploon of a cranked shaft
Condition check, removal and installation of a cover of a distributive chain, chain and its asterisks
Removal, check of a condition and installation of a camshaft, bearings and hydraulic pushers
Removal and pallet installation картера
Removal, check of a condition and installation of the oil pump
Removal and installation of a flywheel/privodnogo of a disk
Replacement of a back epiploon коленвала
Check of a condition and replacement of rubber pillows of support of the engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Replacement of a forward epiploon of a cranked shaft
|
|
Disconnect a negative wire from the battery.
Поддомкратьте redock of the car also establish it on props.
Remove a filter established under a forward part of the engine (protection картера).
Remove приводные belts (the Head of Adjustment and routine maintenance).
Remove a radiator and the fan () cooling systems (the Head of System of cooling, heating and an air conditioning).
Give a fixing bolt демпфера крутильных fluctuations and remove its washer.
|
|
For keeping of a cranked shaft from проворачивания insert two bolts 5/16 * 1-1/2 (inches) into apertures in демпфере and jam between them the lever. Then turn a shaft so that the lever has rested against a frame. |
By means of the special tool remove демпфер крутильных fluctuations from a pin of a cranked shaft.
|
|
|
For removal демпфера крутильных fluctuations use a special stripper, such as it is shown in a picture - do not try to take advantage of a stripper with captures is will lead to damage демпфера.
|
Smooth out and check up a condition of a surface of the central nave демпфера where it contacts to a forward epiploon of a shaft. Insignificant defects can be eliminated by means of an emery paper. If in a nave the deep flute is developed, replace демпфер or in a car-care centre workshop establish in a nave the special loose leaf for restoration of a contact surface.
Having hooked an epiploon the special tool or a screw-driver, cautiously take it from a cover of a distributive chain. Try not to scratch a wall of a nest and not to damage a surface of a pin of a shaft.
|
|
Take an old epiploon, having hooked its special tool (as shown here) or a screw-driver.
|
Smooth out nest walls in a cover and grease external edges of a new epiploon with pure impellent oil or universal greasing. By means of the replaceable face head which external diameter corresponds to external diameter of an epiploon cautiously begin to knock an epiploon in a nest a hammer. Instead of a head the short piece of a pipe of the corresponding diameter can be used. Make sure that in the course of installation of an epiploon the broad spring has not jumped out of it.
|
|
|
Accurately begin to knock a new epiploon in a nest by means of a hammer and a replaceable face head.
|
Grease a contact surface of a nave демпфера крутильных fluctuations by pure impellent oil.
Combine шпоночный a nave groove демпфера with шпонкой in a pin of a cranked shaft and cautiously begin to knock демпфер on a pin a hammer with soft the brisk.
Establish a fastening bolt демпфера крутильных fluctuations and tighten it with demanded effort.
Installation of the remained components make in an order, the return to a removal order.
Start the engine and check up it on leaks.
|
