Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
- Body
   The general information
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Service of loops and locks
   Replacement wind and motionless glasses
   Removal, installation and adjustment of position of a cowl
   Removal and installation of the lock of a cowl and cable of its drive
   Removal and installation to the place of the panel of a decorative lattice of a radiator
   Removal and installation of a forward wing
   Removal and installation of bumpers
   Removal and installation of the panel of an internal upholstery of a door
   Removal, installation and adjustment of position of a door
   Removal and installation of handles, the cylinder and clamp (latch) of the lock of a door
   Removal and installation of a windowpane of a door
   Removal and installation of a regulator of a window of a door
   Removal and installation of the central console
   Removal and installation of the panel of an upholstery of a door of a back
   Removal, installation and adjustment of position of a door of a back
   Replacement of an emphasis of a door of a back
   Removal and installation of facing of a combination of devices
   Removal and installation of facings of a control panel
   Removal and control panel installation
   Removal and installation of covers of a casing of a steering column
   Removal and installation of rear-view mirrors
   Remove also lattice installation обтекателя
   Removal and installation of seats
   Control кузовные the sizes
+ System of an onboard electric equipment
+ Controls and operation receptions




Removal and installation of bumpers

The prevention in the beginning see Has undressed Removal and installation to the place of the panel of a decorative lattice of a radiator.

The forward

 PERFORMANCE ORDER

  1. The forward bumper on cars of the given models consists of the bottom facing and the cross-section beam welded on a frame actually playing a role of a bumper. Disconnect a negative wire from the battery and remove the panel of a lattice of a radiator (Has undressed Removal and installation to the place of the panel of a decorative lattice of a radiator).
  2. Remove assemblages of the right and left head block headlights, lateral dimensional fires and indexes of turns (the Head System of an onboard electric equipment).
  3. Remove clamps of facing of a forward bumper.
  1. Remove the top and bottom clamps of the panel of facing of a bumper.
  1. Remove plastic rivets from a forward part локеров wings.
  1. Remove fastening clamps локеров wings to bumper facing.
  1. Remove facing of a bumper from fixing pins, having taken advantage of a small screw-driver for отпускания lock uvulas under support of indexes of turns.
  2. Installation make upside-down.

The back

 PERFORMANCE ORDER

  1. Поддомкратьте a back of the car also establish it on props.
  2. On the models equipped with the hook-on device (turnbuckle), disconnect electroconducting, then, holding a turnbuckle, give fixing nuts and lower assemblage on the earth.
  1. Before removal of a back bumper it is necessary to remove assemblage of the hook-on device.
  1. Holding a bumper, remove clamps локеров wings.
  2. Give fixing bolts of arms and remove a beam of a bumper with the panel of facing from the car.
  1. Give bolts of an arm of a bumper.
  1. Remove basic arms from a bumper.

Details of installation of a back bumper.

  1. Installation make upside-down.