Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
+ Automatic transmission
- Distributing box
   The general information
   Adjustment of draught of switching
   Removal and installation of a distributing box
   Major repairs of a distributing box - the general information
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions

e65f60b7

Adjustment of draught of switching

NР231

 PERFORMANCE ORDER

    On models 1993 вып. Translate a distributing box in a mode 4L; on models 1994 вып. Translate it in neutral position. On models 1995 вып. Translate a distributing box in position 4L and fix the lever of switching of modes in this position, by means of a wire (a coat hanger for clothes perfectly will approach). Поддомкратьте the car also establish it on props. Loosen the a bolt in a pin of a rod of a choice.
    Loosen the a lock bolt in a pin of a rod of a choice (transmission NP249 is shown - for NP231 the picture is similar).
    Make sure that the lever of switching of a distributing box is in position 4L (models 1993 and 1994 вып.) or in position N (Neutral) (models 1994 вып.). In case of need translate a pin forward or back on a choice rod, then tighten a lock bolt of a pin with demanded effort. Lower the car on the earth and check up serviceability of functioning of the device of switching of a distributing box. Spend trial runs, having made sure of full gearing of a distributing box in positions 2Н, 4Н and 4L. If full gearing in all three modes does not occur, make repeated adjustment.

NР242

1993

Components of draught of switching of distributing box NР242 of models 1993 вып.


 PERFORMANCE ORDER

    Remove facing of the lever of switching. Translate the lever in position 4L. Insert the adjusting prorate in the thickness of 3 mm (the drill of the necessary thickness will approach also) between the lever of switching and an aperture first line under the lever.
    For adjustment of draught of switching of distributing box NР242 of models 1993 вып. Insert the adjusting prorate in the thickness of 3 mm (the drill of a demanded thickness not is worse will approach) between the lever of switching and an aperture first line under the lever (fix the lever and the prorate by means of an insulating tape or a wire).
    Поддомкратьте the car also establish it on props. Under the car ослабьте a lock bolt of a pin of draught of switching also make sure that the switching rod is freely established in a pin and the lever. Make sure that the lever of switching of modes of a distributing box is in position 4L. Freely establish a draught rod in the lever of modes. Strongly tighten a lock bolt of a pin. Clean jacks and lower the car on the earth. Remove the adjusting prorate (drill) and establish into place all earlier removed components.

1994 and 1995

Components of draught of switching of the distributing box NР231 interfaced with РКПП (the same concerns also draughts of switching of distributing boxes NР242 of models 1994 and 1995 вып. And all boxes of type NР249 established complete with РКПП)

Components of draught of switching of the distributing box NР231 interfaced with АТ (the same concerns also draughts of switching of distributing boxes NР242 of models 1994 and 1995 вып. And all boxes of type NР249 established complete with АТ)

Procedure of adjustment of draught of switching of distributing box NР242 of models 1994 and 1995 вып. It is similar that for NР231 1994 (at the switching lever established in position N, instead of 4L). Item 1-7 See.

NР249

Procedure of adjustment of draught of switching of distributing box NР249 of models 1993 and 1995 вып. It is similar that for box NР231 1994 (at the switching lever established in position N, instead of 4L). Item 1-7 See.