Jeep Grand Cherokee
+ Cars of mark Jeep Grand Cherokee
+ Options and routine maintenance
+ Рядный the six-cylinder engine
+ Engine V8
+ Procedure of the general and engine major repairs
+ Systems of cooling, heating and air conditioning
+ The power supply system and release of the fulfilled gases
+ System of an electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of a gear change
- Automatic transmission
The general information
Diagnostics of malfunctions - the general information
Removal and installation of the lever of switching
Check of a condition and adjustment of a cable of switching
The description, replacement and adjustment of a cable of a drive throttle заслонки in a mode kik-daun (TV-cable)
Serviceability check, adjustment and replacement of the gauge-switch of the permission of start
Adjustment of a cable lay блокиратора
Check of a condition and replacement of a support of transmission
Epiploon replacement
The design description, removal and installation of lines and hoses of cooling of transmission
Removal and installation of an additional cooler
Removal and installation of automatic transmission
Replacement of the module of management with transmission (ТСМ) (only for АW-4 and 42RЕ)
Diagnostics of system of electronic control by automatic transmission
+ Distributing box
+ Coupling and трансмиссионная a line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of an onboard electric equipment
+ Controls and operation receptions
|
Epiploon replacement
Leaks трансмиссионной a liquid result from deterioration of an epiploon of lengthening картера transmission or a distributing box (model 4WD) and-or sealing rings of the gauge of speed/nozzle of a speedometer more often. Procedures of replacement of these epiploons and sealing rings are rather simple, as transmission removal, or a distributing box (all-wheel drive models) with the car do not demand.
Lengthening epiploon kartera / a distributing box
The lengthening epiploon картера is located in an extreme back point картера transmission or a distributing box where to them it is connected карданный a shaft. If there are suspicions on leaks through the given epiploon, поддомкратьте the car and establish it on props. If the epiploon really leaks, on a forward part карданного a shaft there will be traces трансмиссионной liquids. The liquid can drip also from a back part of transmission / a distributing box.
|
Remove карданный a shaft (the Head Coupling and трансмиссионная a line).
By means of a hammer with soft brisk cautiously bring down back the dustproof screen (if the such is provided) and remove it from transmission. Try not to bend the screen.
Cautiously having hooked a special stripper, take an epiploon from a back part of transmission / a distributing box. Try not to damage шлицы a secondary shaft of transmission.
|
By means of a screw-driver or mount cautiously take an epiploon from a back part of transmission or a distributing box (try not to damage шлицы a secondary shaft of transmission).
|
If the epiploon does not manage to be taken by means of a screw-driver or mount, take advantage of a special stripper (ask in shops of automobile accessories).
|
If the epiploon does not manage to be taken by means of a screw-driver or mount, take advantage of a special stripper (ask in shops of automobile accessories).
|
Having taken advantage in quality выколотки of a piece of a pipe or very deep replaceable head, establish a new epiploon. Track that it has completely sat down in the nest.
|
By means of a piece of a pipe or a deep replaceable head plant into place a new epiploon; fill it in a nest perpendicularly and on the end make sure of completeness of landing.
|
Establish the dustproof screen, accurately having begun to knock it. Grease шлицы a secondary shaft of transmission lateral aspect sliding муфты the holder крестовины with easy greasing, then establish into place карданный a shaft. Try in the course of installation карданного a shaft not to damage a sponge of a new epiploon.
|
|
Sealing rings of the gauge of speed of the car (VSS) / speedometer nozzles
Assemblage of a VSS/nozzle of a speedometer is located on the left lateral wall of lengthening картера transmissions on models 2WD, or on a back wall of a distributing box on models 4WD. For definition of signs of leaks through a sealing ring examine on presence of traces трансмиссионной liquids a casing drive a cable.
|
Assemblage of a VSS/nozzle of a speedometer is located on a back wall of a distributing box (model 4WD, shown on a picture) or on the left wall of lengthening картера transmissions on models 2WD. For assemblage removal disunite an electric socket (1), mark assemblage position in relation to картеру (2), then give a bolt (3).
|
|
Disunite electric socket VSS.
If assume to establish into place an old nozzle of a speedometer, mark its position in relation to a lengthening surface картера transmission or a distributing box; If the nozzle is replaced, at installation new it is necessary to take care of correct orientation of its digital index - see below (item 16).
Give a bolt of fastening of the gauge and a nozzle clip.
Remove VSS and a speedometer nozzle.
Examine probes of socket VSS. In case of need they can be smoothed out by means of special aerosols for cleaning of electric contacts.
Remove old sealing rings from the gauge and from a nozzle.
Carefully smooth out interfaced surfaces of a flange of a nozzle and картера is it is necessary for the purpose of correct centering of a nozzle at its installation.
Establish sealing rings on VSS and a nozzle.
|
By means of a small screw-driver or a core with a hook on the end (as is shown in a picture) remove old sealing rings; try not to damage a surface of flutes under their installation.
|
|
Components of typical assemblage of a VSS/nozzle of the speedometer established on transmission.
|
|
Components of two typical assemblages of a VSS/nozzle of the speedometer, established on a distributing box. |
Grease sealing rings of the gauge and a nozzle трансмиссионной with a liquid.
Establish VSS in a speedometer nozzle. Tighten with demanded effort the fixing screw.
Establish in a nozzle a speedometer gear wheel.
If the new nozzle is established, before its installation in gathering with the gauge (VSS) count quantity of a teeth on a speedometer gear wheel.
Grease a gear wheel teeth трансмиссионной with a liquid.
Establish assemblage VSS with a nozzle in lengthening картера transmissions or a distributing box.
If the old nozzle is established, simply take care of combination of landing labels (put in the course of dismantle) on a nozzle and surface flange картера transmission lengthenings / a distributing box. At installation of a new nozzle follows, rotating it, to achieve, that the numerical index put on its surfaces which value corresponds to quantity of a teeth of a gear wheel, it has appeared turned in position at 6 o'clock.
|
Numerical indexes on a wall of a nozzle of the speedometer, corresponding to various quantity of a teeth of a gear wheel of a speedometer (on different models gear wheels of various types can be used); at installation the index corresponding to number of teeth of a gear wheel applied on the given car of a speedometer should be turned in position at 6 o'clock.
|
Establish a clip of a nozzle of a speedometer and the fixing screw. Tighten the screw of a clip with demanded effort.
Connect an electric socket.
Clean jacks and lower the car on the earth.
Make trial runs, having checked up speedometer work, then make sure of absence of signs of leaks through a lengthening epiploon картера transmissions / a distributing box and sealing rings of a VSS/nozzle of a speedometer.
|
|
|
|